Hi Guys,
Can'r figure out this little gizmo...
Unit came with a T connector, and a 7mm small tube....
What is he small tube for ?
Does the 90 degrees way of the connector go to the inlet ?
There is a small screw with Phillips head - is this for adjusting the triggering flow ?
On the back there is a knob you can turn an arm that pushes the spring - what does this do ?
A diagram or few words will help a lot....
Many thanks
Isaac
water flow/pressure sensor connection LSR-H2OPRSN
-
- Posts: 27
- Joined: Sat Aug 22, 2015 7:15 pm
- Contact:
-
- Posts: 9
- Joined: Thu Mar 31, 2016 10:04 am
- Contact:
Re: water flow/pressure sensor connection LSR-H2OPRSN
What is the small tube for ?
ANS: The tube is to connect the T connector with the water sensor.
Does the 90 degrees way of the connector go to the inlet ?
ANS: YES, T connector go to inlet of the water sensor. It is a little hard to connect both the T connector and the inlet together.
There is a small screw with Phillips head - is this for adjusting the triggering flow ?
ANS: The small screw is to hold the plastic head in place.
On the back there is a knob you can turn an arm that pushes the spring - what does this do ?
ANS: The knob is to adjust the triggering pressure. If you have a low volume output water pump, make sure the plastic head with a screw is in a low position.
ANS: The tube is to connect the T connector with the water sensor.
Does the 90 degrees way of the connector go to the inlet ?
ANS: YES, T connector go to inlet of the water sensor. It is a little hard to connect both the T connector and the inlet together.
There is a small screw with Phillips head - is this for adjusting the triggering flow ?
ANS: The small screw is to hold the plastic head in place.
On the back there is a knob you can turn an arm that pushes the spring - what does this do ?
ANS: The knob is to adjust the triggering pressure. If you have a low volume output water pump, make sure the plastic head with a screw is in a low position.
-
- Posts: 27
- Joined: Sat Aug 22, 2015 7:15 pm
- Contact:
Re: water flow/pressure sensor connection LSR-H2OPRSN
Thanks for the answer.
IMHO - this information should be sent with the product itself, ths way you can avoid these kind of questions...
Cheers
Isaac.
IMHO - this information should be sent with the product itself, ths way you can avoid these kind of questions...
Cheers
Isaac.
-
- Posts: 2
- Joined: Sat Feb 23, 2019 5:07 am
- Contact:
Re: water flow/pressure sensor connection LSR-H2OPRSN
I agree with above. I have 60 watt laser and have no way of knowing how to wire water sensor up for it to work properly. Any information would be great
-
- Posts: 2
- Joined: Sat Feb 23, 2019 5:07 am
- Contact:
Re: water flow/pressure sensor connection LSR-H2OPRSN
I have a cw3000 chiller and it came with a sensor plug. How would I go about wiring it up to that?
-
- Posts: 492
- Joined: Fri Jan 20, 2012 1:39 pm
- Location: Appelscha, the Netherlands
- Contact:
Re: water flow/pressure sensor connection LSR-H2OPRSN
On page 5 of the manual you will find the connection:
https://www.hi-end.ro/upload/files/CW-3000-hiendro.pdf
Kees
https://www.hi-end.ro/upload/files/CW-3000-hiendro.pdf
Kees
Who is online
Users browsing this forum: No registered users and 1 guest