Lightobject.com Support Forum

spektrum wrote:So is it possible to alter the 'laserstart' macro to automatically start the laser cutting process? Alternatively can you create a shortcut key for the 'start' button in LaserCAD?

No you can't. You need to use LaserCad to set the speed and power before it start to process your job file

Marco

Hi Marco,

Where can I find the DSP software to suite my board ( order #85753B)?

Thanks.

Cheers,
David.

o999 wrote:Hi,

Can I get a link?

Order #85753B (March 2011)

Thanks,
David.

David, are you running LaserCad or PHCad?
I don't have any update for PHCad

Send me a picture of the mainboard if you can

Marco

Tech_Marco wrote:David, are you running LaserCad or PHCad?
I don't have any update for PHCad

Send me a picture of the mainboard if you can

Marco

Hi Marco,

A picture of the main board is attached.

I'm not running any software with the board at the moment as it hasn't been installed. I bought the board to upgrade a laser printer running the "infamous" MoshiDraw, but for various reasons I was delayed in completing the project.

Basically I am just hoping to end up with something usable, so whatever software is available I'll try.

Thanks.

Cheers,
David.

David:

That's an older DSP board (I named it 2011 DSP) that 'we' stop making or selling after 2011. The programmer formed a new company and came up a new DSP card "AWC608" on 2012 and that is the card that I'm carrying. That's a long story about that card 2011 (not a please one .

Anyway, you need "PHCad" instead. See the link here: viewtopic.php?f=55&t=660


Marco

Tech_Marco wrote:David:

That's an older DSP board (I named it 2011 DSP) that 'we' stop making or selling after 2011. The programmer formed a new company and came up a new DSP card "AWC608" on 2012 and that is the card that I'm carrying. That's a long story about that card 2011 (not a please one .

Anyway, you need "PHCad" instead. See the link here: viewtopic.php?f=55&t=660


Marco

Hi Marco,

I have seen that link before - but where can I get the PHCad software?

Cheers,
David.

Hi Marco,

I just searched and found a copy of PHCad_v4.38 that I downloaded in March 2011.

Is that the only software I will need to drive the controller?

Thanks.

Cheers,
David.

o999 wrote:

Tech_Marco wrote:David:

That's an older DSP board (I named it 2011 DSP) that 'we' stop making or selling after 2011. The programmer formed a new company and came up a new DSP card "AWC608" on 2012 and that is the card that I'm carrying. That's a long story about that card 2011 (not a please one .

Anyway, you need "PHCad" instead. See the link here: viewtopic.php?f=55&t=660


Marco

Marco
I also need the firmware and lasercad please
My order number is 200818
My email docwiz3@bigpond.com
Thanks

Can I get the software as well please Order # 200763

Ordernr 201031
Please send me the link too..

Kees

Hello Marco,

Please also send me the Firmware and LaserCad Software.

Order number: 201023

THANKS!

Hello Marco,

Please send me the Firmware and LaserCad Software.

Order number: 198989

regards


Andrea

Hi Marco

What is the latest Lasercad version?? (and AWC608)
I am still having real problems trying to sort my machine..... (awful engraving).... so I decided to completely reinstall everything so I can "fault find" with no legacy on the machine or PC.



Thanks

John

John. There is no new update software available. The software has nothing to do with the engraving or cutting. You need to check your parameter setup and/or mechanic & wire connection.

Marco

Tech_Marco wrote:John. There is no new update software available. The software has nothing to do with the engraving or cutting. You need to check your parameter setup and/or mechanic & wire connection.

Marco

Hi Marco.

Ah well i was hoping there'd be a version to woark directly with corel draw 6.
As for my other issues i will open a new thread

John